Hello. Thanks for mapping
A remark. When you map a bridge over a stream or river , always add a tag
Layer=+1 to that part of the highway where it crosses the waterway
This means that the bridge and the water are on different levels. Run a validation on your work. I pops up instantly
Thanks

Hello . Thanks for mapping
Please square all buildings you map with the q key in iDeditor, Map the buildings more accurate please.
Also map ALL buildings nearby the spot you are mapping.
Best regards and keep mapping.

Hi Sehersr. Thanks for mapping here.
A question. Do you have local knowledge about the features you have mapped?
you map restaurants and caf'es here.
Please just map a building as building=yes.
Do not forget to square each building with the Q key in iDeditor.
Please map all buildings on the spot were you are mapping on. Otherwise other mappers have to go over it again.
You missed also to extend an incoming highway from another task.
Best regards and keep mapping

Hello John. Thanks for mapping on this project. You left a lot of correction work to other mappers/validators.
You did not square the majority of your buildings with the Q key in iDeditor.
Please do not connect nodes of buildings to other buildings or features
and be more accurate in following the outlines of buildings. You often map a building oversized,
This is a building/highway project. Please restrict yourself to that, rather than mapping farmland. ( these areas have to be mapped out of a project because in these project you are limited to the task were your are working on and it is beyond the scope of the project
Best regards and keep mapping

Another issue
This is a buillding/highway project.
Please don't map other features.
It makes no sense to map a tiny part as woods . Woods and other natural objects needs to be mapped out of the disaster projects. On this TM3 site you are restricted to the task you are working on,
Best regards

Hello. Thanks for mapping here. I review mappers work and have a remark.
Please don not collect several buildings in 1 mapping. Map each building as a single building.
Best regards

Hello Sandra. Thanks for mapping here.
I review mappings and have a few remarks.
Please be more precise in your mappings, map all buildings and square them with the Q key in iDeditor, Do not map a highway through buildings. Nav systems don't like that, nor do the drivers,
Do not connect nodes of buildings to other objects.
Didn't you notice the warning triangle (right hand menu) with in your case 11 warnings? ! they should be solved before you upload your work.
Best regards and keep mapping

Hello Ben Viggars
Thanks for mapping here.
A few remarks. Do not connect nodes of highways to buildings. Try to connect them only to other highways and don't let gaps open between pieces of highways.
Try to map as simple as possible. A building is mostly straight rectangular with 4 or 6 nodes. When you see a tree covering a building, extrapolate the side of the building.
Don't forget to square each building in IDeditor with the Q key. Please pay also attention to the issues give by the warning triangle on the right side menu and solve them if possible.
You overlooked 5 warnings
From the 24 buildings you have mapped are 16 not squared.
Best regards and keep mapping

Hello NJDE 1905
Thanks for mapping here
A request. Please map more accurate. Your mappings are often much oversized.
Also square all buildings with the Q key in iDeditor.
Best regards and keep mapping

Another issue.
Please try to read a imagery more careful.
You mapped a number of buildings which are actual pieces of a highway visible between trees. Try to understand where you are looking to .
Best regards

Hello. Thanks for mapping here.
This is a building/ highway task. Please stick to that. It makes no sense to map parts as "wood" since those areas are much bigger than the task square you mapped. These taggings have to be done outside the tasking manager.
The way you map these woods introduces lots of errors which have to be solved as well,
Best regards and keep mapping

Hello. Thanks for mapping here.
A remark. Please map more accurate by following the outlines of the buildings. You tend to oversize your mappings
Also square your buildings with the Q key of iDeditor
Best regards and keep mapping

Hello Harmond. Thanks for mapping here,
A request. Please map more accurate by following the outlines of the building and square them with the Q key in iDeditor.
You mapped 28 buildings of which 27 not squared.
Best regards and keep mapping

Hello. Thanks for mapping.
Please map more accurate and square the buildings you map every time with the Q key on iDeditor
Restrict yourself also to the mapping requirements on these tasks.
Best regards and keep mapping

Hello. Thanks for mapping here.
Please make it a habit not to connect nodes of buildings together and square them with the Q key in iDeditor.
Thanks

Thanks for mapping here. Please be more accurate in your mappings. The buildings you mapped as equal formed buildings don't reflect the reality. Please try to follow the outlines of the buildings. It's tough, I know.
See this page for the adjustments made
https://overpass-api.de/achavi/?changeset=78978541
Best regards

Hello Louiswoo. Thanks for mapping here
Please pay more attention on mapping individual buildings. I guess you used the terassing tool to divide blocks of buildings.
Use these only when the building blocks are suitable for that.
btw Don't connect buildings together with the nodes when you are not sure they share walls.
Best regards

Hello Ronald Jones. Thanks for mapping.
A remark. Didn't you see the issue signs with warnings about crossing buildings. non squared buildings and so on ?
Please solve these issues before uploading.
Square all the buildings you map with the Q key in iD editor
Thanks

Hello, Emy. Thanks for mapping
A request. Please map more accurate (you map rather sloppy) and square each building with the Q key in iDeditor.
Best regards and keep mapping

Hello xanerten, Thanks for mapping here.
Please be more accurate in mapping, do not connect nodes of buildings to eachother and square the buildings with the Q key in iD editor
Best regards and keep mapping