Hello Derek. I reviewed your mappings and noticed that you map open areas as building. Please review these documents
Please see here for new mapping instructions https://drive.google.com/open?id=1bS_TVHPFHKKVBSdjx3RRQdxhdWrMJ3wdEh_BSnsL4hI https://drive.google.com/open?id=1N1rXlAyGcJ6VJ2p3qbD4PRsuo65o3pC5yHB2wq1TGEc
Best regards

Hello SiMcM, I saw your comment about round buildings and checked this changeset. Please use the Maxar P imagery, This is most recent . I quess these settlements are abandoned , the settlement on the top for sure, On the older imagery Bing shows buildings. Maxar shows just vague remainings.
Best regards

Hello. A request. Please square all your rectangular buildings . You squared not a single one !
See this youtube video how to ..
https://www.youtube.com/watch?v=E1YJV6I_rhY
best regards

Hello Chandra. My complements. Very good mappings. I noticed that you corrected a lot of bad shaped mappings. ( Normally a validators job, so thank you very much for that) Just a remark. in a few occasions you connect nodes from buildings to other buildings. Try to avoid that. When you push down the Ctr key during mapping the nodes won't snap.
When you also have installed the "Inline validating " tool, those errors pops up instantly as many others when they occur.
Best regards

Hello Elif, Thanks for mapping here
Would you be so kind to use the MAXAR R imagery on this project? This is more recent and much clearer.
And.... do not forget to square the buildings you have mapped. You are not consequent in squaring them.

Best regards Best regards

On This webpage you can see your mappings and the adjustments which has been made. Also the offset has been corrected so all buildings seems to be displaced a bit
https://overpass-api.de/achavi/?changeset=72510645
See the legend for info
best regards

Hello. Thanks for mapping here. Please pay more attention on the shape of the buildings. You mapped all buildings here as round buildings despite there are quite a number of rectangular buildings as well. The Bing imagery is clear enough to see the difference. Please use at next mappings the Maxar P imagery. More recent and very clear.
Please see here for new mapping instructions https://drive.google.com/open?id=1bS_TVHPFHKKVBSdjx3RRQdxhdWrMJ3wdEh_BSnsL4hI https://drive.google.com/open?id=1N1rXlAyGcJ6VJ2p3qbD4PRsuo65o3pC5yHB2wq1TGEc
siwilde | Crowd2Map Get

Best regards and keep mapping

Hello, Back again
pls take a look to this page where you can see your mappings and the modifications has been made
Best regards
https://overpass-api.de/achavi/?changeset=72479363

Hello. I am reviewing mappings and have some remarks.
Please check if a building is round by watching the shadow on the ground of that object. If its round, its a round building. otherwise rectangular.
No shadow at all, not a building
Both shadows in and outside an object? no building
best regards and keep mapping

Hello Kkatarina. Thanks for mapping here.
a request. Please square the rectangular buildings with the Q key. You overlooked quite a lot of them
Please map a building as a round building as the shadow has also a round for,
Best regards and keep mapping

Hello. Thanks for mapping here.
a remark. Check if you see a shadow near the object you want to map. No shadow=no building.(ground level) Please restrict yourself to mapping of buildings. See instructions. Wood area mapping is not needed. btw This is savanna
Best regards

On this page you find your mappings and the corrections which has been made
https://overpass-api.de/achavi/?changeset=72465474
Best regards

Hello, Thanks for mapping here.
Please pay more attention on precise mapping. Your mappings looks sloppy, because they are oversized and not squared. Do not include the shadow of a building in your mapping and square each building with the Q key in iD editor,
please take a look to this page with your mappings and the changes which has been made
https://overpass-api.de/achavi/?changeset=72465585
red are your mappings, green the adjustments
best regards

Hello, Thanks for mapping here. Somewhat late due to the shortage on validators.
About your mapping skills. I hope they have improved by now. These mappings, sorry to say, are very sloppy, Take a look to the shape. The buildings are mostly strictly rectangular. Please take the time to map them accurate.
Please take a look to these documents for a better understanding of this area
http://www.johntyman.com/africa/ Pages 27 and 28
And these pages
https://drive.google.com/open?id=1bS_TVHPFHKKVBSdjx3RRQdxhdWrMJ3wdEh_BSnsL4hI https://drive.google.com/open?id=1N1rXlAyGcJ6VJ2p3qbD4PRsuo65o3pC5yHB2wq1TGEc
Always square a building you map (except round buildings) with the Q key in iD editor, Do not include the shadow of the building into your mapping.
When you see inside, as well as outside a shadow, there is no roof, so in these settlements it are mostly sheds for their livestock.
Best regards and keep mapping

Hello, Thanks for mapping. A remark,
I noticed that you mark small black spots beneath a building as a building. These spots are the shadow of the adjacent building. When mapping a building, don't include these shadows in a building. When there is a shadow inside as well as outside a building, don't map it as a building. In these settlements that are mostly sheds to keep their livestock.
best regards and keep mapping

Hello Chellay.
A remark. Please map next time with the Maxar P imagery. More recent and clear to map from .
Please square each rectangular building after mapping it. Q key in iD Editor
Best regards and keep mapping

Hello. A remark about your mappings.
you tend to oversize your mappings a bit. Please keep an eye on that. Do not include the shadow of a building in your mapping either,
see this page for more info.
https://overpass-api.de/achavi/?changeset=72461866
Best regards

Hello Rosie. A team of validators are reviewing tasks to see if they are in accordance with the requirements , free of errors and of good quality,
To start with the latter. Sorry to say, but your mapping skills needs to be improved. Your mappings are very sloppy, not squared and often out of place
Please use the Maxar P Imagery. More recent and of good quality to map from.
Don't tag a house with name=building. Building-yes is conform the instructions
Please take a look to these documents
The are very helpful

https://drive.google.com/open?id=1bS_TVHPFHKKVBSdjx3RRQdxhdWrMJ3wdEh_BSnsL4hI https://drive.google.com/open?id=1N1rXlAyGcJ6VJ2p3qbD4PRsuo65o3pC5yHB2wq1TGEc
I don't blame you for using the Bing Image. It might be helpfull to know that these images are dated betrween 2003 and 2013
The Maxar P images dates from 2013
Since these areas are so isolated there is a lack on recently dated images
please take a look to this page. The buildings has been moved to their correct places. But take a look to the difference in size. ( The yellow and lined buildings reflect the correct dimensions) A lot of red buildings were disappeared on Maxar, so I removed them
https://overpass-api.de/achavi/?changeset=72460675

Best regards and keep mapping.

Hello .This task has been reviewed and I have some remarks.
1. Please square the buildings (rectangular) with the Q key in ID editor. You squared not a single building !
Best regards

Abother issue. Please use MAXAR P as imagery for future mappings
best regards